PLYWOOD & MDF · CHINA

Stacked panel edges from our marine plywood rangeOur marine plywood range · view panel-edge detail

OUR FACTORY · PRODUCT DETAILS

18mm Marine Plywood

18mm marine plywood. Ready for your next fitting or assembly.

Source 18mm, eleven-ply marine plywood for boat interiors, supported sole panels, bulkheads and access surrounds. Choose the core and visible faces, then let our factory prepare full sheets or cut parts with openings, fittings and protected edges around your drawing.

Thickness
18mm
Construction
Eleven plies
Factory supply
Sheets / Machined parts

Available to order · 10–15 days production · Container shipping

TECHNICAL DATA · TDS-PS-22 · Rev 2.0 (Oct 2026)

18mm Marine Plywood technical data

Order 18mm marine plywood with an eleven-ply construction and the face, core and finish your project needs. For 1220 × 2440 mm sheets, the Okoume option is about 28.9 kg at 540 kg/m³. The SGS report on this page covers a separate 599 kg/m³ configuration; its corresponding calculated sheet weight is about 32.1 kg.

18mm marine plywood options — technical data sheet TDS-PS-22, Rev 2.0 (Oct 2026). The selected construction is included in your quotation.
Thickness and construction18 mm; 11 plies
Face / Back Veneer SpeciesSelected Rotary or Sliced Okoume (Aucoumea klaineana), Sapele, or Marine Birch (≥ 1.0 mm face)
Core Veneer Construction100% Okoume, 100% Sapele/Mahogany, or Void-Free Selected Eucalyptus/Birch
Adhesive System100% Unextended Phenolic Formaldehyde Resin (WBP — EN 314-2 Class 3)
Standard Sheet Sizes1220 × 2440 mm, 1220 × 2500 mm, 1220 × 3050 mm; larger project formats include 1500 × 3000 mm and 1530 × 3100 mm
Surface Appearance GradeA/B or B/BB (Solid, knot-free, synthetic-patch-free face per BS 1088)
Surface FinishingCalibrated and fine sanded both sides (180# grit)
Thickness Tolerance18 mm: ±0.3 mm (BS 1088 / EN 315)
Length & Width Tolerance±1.0 mm (BS 1088 / EN 315)
Squareness≤ 1.0 mm / m (EN 324-2)
Core Gap & Overlap SpecificationZero overlaps; max occasional edge pin-gap ≤ 0.5 mm (Edge-glued / stitched whole-piece plies)
Core Void LimitZero internal overlaps; max edge gap ≤ 0.5 mm (BS 1088)
Service Class / Exposure DutyService Class 3 (Marine Hull/Deck Joinery, Yacht Interiors & Severe Exterior Exposure)
Reference StandardsBS 1088:2018, EN 636-3, EN 314-2 Class 3, ISO 1096
Harmonized System (HS) Code4412.31 / 4412.33
Physical and mechanical properties (declared values)
Density (100% Okoume / Sapele / Eucalyptus-Birch), kg/m³500–550 (Okoume) / 620–680 (Sapele/Hardwood)
Test method: EN 323 / BS 1088
Moisture Content at Dispatch, %8.0 – 12.0
Test method: EN 322
Bending Strength — Longitudinal (MOR //), MPa≥ 46.0 (Okoume) / ≥ 62.0 (Sapele/Hardwood)
Test method: EN 310
Bending Strength — Transverse (MOR T), MPa≥ 34.0 (Okoume) / ≥ 46.0 (Sapele/Hardwood)
Test method: EN 310
Modulus of Elasticity — Longitudinal (MOE //), MPa≥ 5,200 (Okoume) / ≥ 7,000 (Sapele/Hardwood)
Test method: EN 310
Modulus of Elasticity — Transverse (MOE T), MPa≥ 3,900 (Okoume) / ≥ 5,400 (Sapele/Hardwood)
Test method: EN 310
WBP Bond Shear Strength (72h Continuous Boil), MPa≥ 1.2 MPa (Mean Wood Failure ≥ 85%)
Test method: EN 314-2 Class 3 / BS 1088
Thickness Swelling (24h Water Immersion), %≤ 6.0
Test method: EN 317
Formaldehyde Release, mg/m³≤ 0.05 (Phenolic Resin — E0 / CARB P2 Compliant)
Test method: EN 717-1
Two 18mm, eleven-ply configurations — 1220 × 2440 mm sheets
ConfigurationDensityCalculated area weightCalculated sheet weight40HQ quantity
Okoume option — TDS planning basis540 kg/m³9.72 kg/m²28.9 kg~895 sheets, indicative
Configuration covered by the SGS report599 kg/m³, recorded in the report10.782 kg/m²32.1 kgCalculated with the order packing plan

The SGS report records the 599 kg/m³ density for its 18mm configuration and selected BS 1088-1:2003 checks. The area and sheet weights above are calculated from that density and the nominal dimensions; they are separate from the 540 kg/m³ Okoume loading reference. View the SGS report and its configuration.

For other thicknesses and ply schedules, compare the marine plywood range.

Weight basis: nominal thickness × 1220 × 2440 mm × 540 kg/m³ for the Okoume loading reference, before finish, fittings or packing. Container quantities are indicative for this configuration; the final loading plan includes actual board weight, pack dimensions, packaging and the container payload limit. Hardwood options use their own weight and packing schedule.

Order options for 18mm Marine Plywood

Sizes, finishes & supply requirements

CONSTRUCTION & SUPPLY CONDITION

Our product configuration and order requirements
Thickness and construction18mm, eleven plies; selected veneer species and layup included in the order.
Face and core choicesOkoume, Sapele or Marine Birch faces; all-Okoume, Sapele/Mahogany or selected Eucalyptus/Birch core constructions.
Surface selectionA/B or B/BB for the technical configurations; visible faces, repair range and chosen finish recorded with the sample.
Standard formats1220 × 2440mm, 1220 × 2500mm and 1220 × 3050mm.
Larger project formats1500 × 3000mm and 1530 × 3100mm, selected with the 18mm construction and quantity.
Marine and bond requirementsSelected BS 1088 marine requirement and phenolic WBP bond; applicable report, standard edition and configuration identified with the order.
Finished dimensions18mm technical-data tolerance ±0.3mm; length/width ±1.0mm and squareness ≤1.0mm/m. Specify the measured interval and supply stage for fitted parts.
Openings and fittingsPart outline, cut-out position, corner radii, hole pattern, backing footprint and tool access from the current drawing.
Factory processingFull sheets, blanks or machined parts; identify reference face, grain direction, openings and critical fit dimensions.
Protective finishBoth faces, perimeter, opening edges, hole walls and surfaces created by later cutting or adjustment.
Weight configurations1220 × 2440mm: about 28.9kg at the 540kg/m³ Okoume planning basis; about 32.1kg calculated at the separate 599kg/m³ SGS configuration. Finish, hardware and packing added separately.
Samples and documentsFull-thickness face/edge sample and a working fitting or opening detail; product data, relevant report and inspection requirements for that construction.
Quantity and packingSheet or part counts, complete sets, drawing revision, face protection, edge support and pack identities for the destination.

Choose the construction, finish and size for your project. We’ll bring the selected options and finished tolerances together in your quotation.

FULL SHEETS · OPENINGS · FITTED PARTS

Order the 18mm marine panel your workshop needs

Start with the component you are making: a supported sole panel, bulkhead, access surround or equipment mounting. Our factory can supply full sheets, rectangular blanks or prepared parts, with the chosen faces, openings and protected edges included in the quotation.

Send your drawing or existing panel reference with the quantities and destination. We help connect the marine construction to the machining, finish and fitting detail, so you can compare the material and the factory work together.

Decisions that change the material or processing quote
Order requirementInclude in the enquiryCompare with your part
18mm and eleven pliesActual thickness limits, veneer species and layup.The complete veneer construction and finished panel dimensions.
Marine material requirementNamed standard, edition, class and requested evidence.Panel qualification and the finished assembly's design requirements.
Large machined openingPosition, corner geometry, retained strips and support drawing.The outside blank size and the remaining material after machining.
Bolted fittingFitting base, holes, backing, bedding, fastener and access space.A clear hole on the top face and a complete fitting that can be installed beneath it.

Match metric thickness to the fitting

Three-quarters of an inch is 19.05mm, or 1.05mm more than 18mm. For a replacement panel, channel or rebate, send the measured fit and required thickness interval. The quotation can then identify the finished dimensions your workshop needs.

Comparing with 12mm marine plywood? At equal area and density, an 18mm panel contains 1.5 times the material volume and mass. Keep the required panel properties, supports and connections with the component design when selecting its thickness.

18MM MARINE PLYWOOD · ELEVEN-PLY CONSTRUCTION

Choose the timber, faces and supplied stage

Our range includes an 18mm, eleven-ply construction. Specify the face, reverse and inner veneer species together with the surface selection and finished dimensional limits. This keeps the panel your team approves connected to the parts it receives.

Timber and visible faces

For Okoume throughout, review the all-Okoume marine plywood route. Choose both faces around the intended clear finish, paint or covering, and include visible edges or adjoining-panel matching in the appearance reference.

Sheets or prepared components

Choose full sheets for your workshop, oversize blanks for final machining, or drawn parts with completed openings and edges. Mark the supply stage and the work you want finished before dispatch.

The 599kg/m³ report configuration is the identified 18mm, eleven-ply, 1220 × 2440mm product. The 540kg/m³ Okoume weight schedule is a separate planning configuration. We keep the selected core, data and sample together when preparing your order.

BOAT INTERIORS · WET AREAS · EQUIPMENT FITTINGS

Plan the panel around its installed detail

Supported soles and access surrounds

Identify the removable cover and fixed surround, with their supports, attachments and walking-surface finish. We help prepare the faces, cut parts and protected edges for each component.

Bulkheads and service openings

Show the outside shape, opening positions, grain direction and attachment interfaces. Include the structural or interior role from your design so the construction and processing follow the same brief.

Equipment bases and bolted fittings

Send the fitting footprint, holes and backing detail with the space available behind the panel. A sample around the nearest opening can help your workshop review both faces, the completed fit and installation access.

Laminated or reinforced components

Two nominal 18mm sheets total 36mm before bondlines, preparation and finish. For a laminated transom or reinforced support, supply the assembly design, joint and bonding requirements with the sheet schedule.

For waterproof boat and wet-area applications, choose the marine bond with the coating and edge-treatment plan. Include outside edges, openings, hole walls and later installation cuts so the protective finish follows the completed component.

OPENING POSITION AND RETAINED MATERIAL

Set out the opening from the panel's reference edges

For layout planning, use a 1200 × 800mm blank with a 600 × 400mm rectangular opening. Centred, it leaves 300mm at each end and 200mm above and below. Moving the same opening 100mm to the right leaves 400mm at the left and 200mm at the right.

Dimensions measured from the same outside edges; square-corner geometry only
Opening positionLeft / right remaining widthTop / bottom remaining widthNet panel area
Centred: left edge at 300mm300 / 300mm200 / 200mm0.7200m²
Shifted: left edge at 400mm400 / 200mm200 / 200mm0.7200m²

Both layouts remove 0.2400m² from a 0.9600m² blank and leave 0.7200m². The retained widths and available connection space differ, so dimension the opening's position as well as its size. Add corner radii, nearby holes, edge profiles and support locations to the production drawing.

These rectangular inputs make the layout comparison easy to follow. Your actual corner geometry, retained strips and supports stay with the component design and machining sample.

SPACE FOR THE COMPLETE FITTING

Check the backing footprint beside an opening

Use the centred opening above and measure downward from the blank's top edge. The layout below uses a 10mm-diameter hole at x = 600mm, y = 160mm and a 240 × 120mm backing footprint centred on the hole. Its lower hole edge is at 165mm, leaving 35mm to the opening at y = 200mm.

Read the worked detail and calculations

The backing reaches y = 220mm, creating a 20mm overlap across its 240mm width. Moving the hole centre to y = 120mm puts the backing edge at 180mm and leaves a 20mm geometric gap. The hole edge then sits 75mm from the opening.

Hole at y160 clears the opening but its 240 by 120mm backing footprint overlaps by 20mmBacking overlaps the openingHole centre: x600 / y160mm600 × 400mm opening1200 × 800mm panel outlineHole edge to opening: 35mmRed strip: 20mm backing overlapPlan view · dimensional clearance layout
Review the whole footprint. The hole is in retained material, while 240 × 20mm of the backing extends into the opening.
Moving the hole centre to y120 leaves a 20mm geometric gap between backing and openingBacking clears the openingHole centre: x600 / y120mm600 × 400mm opening1200 × 800mm panel outlineHole edge to opening: 75mmBacking edge to opening: 20mmPlan view · dimensional clearance layout
Review the revised assembly. The shifted backing clears the opening; include bearing, edge distances, sealing and tool access with the connection design.

Use the common-scale drawings to check the space needed on both sides of the panel. Bring the actual backing material, thickness and fixing requirements into your drawing, then try that detail on the selected marine construction.

THROUGH-BOLT LENGTH AND INSTALLED THICKNESS

Include every layer beneath the bolt head

The following dimensional calculation uses a non-countersunk through-bolt measured from under its head: a 4mm fitting base, the compressed bedding shown in the table, 0.40mm total finish on both panel faces, a 6mm backing piece, a 2mm washer and an 8mm nut. Use your actual hardware dimensions when selecting the installed fastener.

Dimensional stack to the nut's outer face, using the hardware inputs below
Panel / compressed beddingComplete stackLength for 3mm projection inputProjection with 45mm length
17.70 / 0.80mm38.90mm41.90mm6.10mm
18.00 / 1.00mm39.40mm42.40mm5.60mm
18.30 / 1.20mm39.90mm42.90mm5.10mm

At the middle case, 18.00 + 4.00 + 1.00 + 0.40 + 6.00 + 2.00 + 8.00 = 39.40mm. A 40mm under-head length projects 0.60mm beyond the stack; the calculation's 3mm projection target needs 42.40mm. At 45mm, the projection is 5.60mm.

The 3mm projection is an input for this comparison. Select the fastener using the hardware manufacturer's thread-engagement and shank requirements, washer arrangement and tightening method. Include compressed bedding, bearing contact and the clearance needed to reach the nut or equipment behind it.

MACHINING AND PROTECTIVE FINISH

Complete the opening, hole and finish as one process

Support the retained frame

Plan workholding and the cutting sequence around what remains after the opening is removed. Support the frame and control the released cut-out, then review the corner profile, exposed layers and entry or exit edges.

Inspect before finishing

Check cut edges and hole walls while they are visible. Keep the required surface condition and any repair process with the panel specification and part reference.

Prepare each penetration

Define the protective coating, bonded insert, sleeve or other specified detail with the actual fitting. Include the finished bore, fitting base, preparation and cure stages in the supplied work.

Complete later adjustments

Carry the protection around perimeter edges, openings, holes and recesses. Re-treat fresh wood exposed during installation. For an epoxy-based finish, include the compatible final coating and sunlight protection for the intended exposure.

Allow for finish inside the bore

Using a 10.00mm bare hole and 0.25mm of finish on each opposing wall gives a 9.50mm finished diameter. With an 8.00mm bolt, clearance is 1.50mm across the diameter, or 0.75mm radially when centred. Measure the completed bore and try the actual fitting, including the re-protection process if final machining is needed.

PANEL MASS AND COMPLETED PARTS

Plan weight with the construction you are ordering

The four formats compared below show nominal panel volume at 18mm. Select the format with the core, layup and order quantity; use the chosen construction's density or measured weight for the handling and shipment plan.

Range formats expressed as width × length; calculated volume at 18mm
Sheet formatAreaNominal volume
1220 × 2440mm2.9768m²0.0535824m³
1220 × 2500mm3.0500m²0.0549000m³
1500 × 3000mm4.5000m²0.0810000m³
1530 × 3100mm4.7430m²0.0853740m³

A 1220 × 2440 × 18mm sheet contains 0.0535824m³. At the 540kg/m³ Okoume planning basis, its calculated bare-panel weight is about 28.9kg. Using the separate 599kg/m³ SGS report configuration at the same nominal dimensions gives about 32.1kg. Keep these configurations separate on the quotation and packing plan.

Include the opening and fitted components

At 540kg/m³ and 18mm, the 1200 × 800mm blank contains 0.01728m³ and weighs about 9.331kg. A 600 × 400mm opening leaves 0.01296m³ and about 6.998kg of panel. Adding a 1.800kg planning allowance for hardware, backing and retained finish gives about 8.798kg.

The cut-out removes about 2.333kg; with that 1.800kg allowance included, the completed assembly is about 0.533kg lighter than the original bare blank. Replace the allowance with your actual fitted parts and finish. Keep the remaining shape, lifting method and support with the handling plan.

Protect sheets and machined parts with flat support, suitable separators and edge protection. The final gross shipment weight also includes pallets, covers and restraints, while finished parts follow their coating's packing requirements.

SHEET YIELD AND RECOVERED PARTS

Compare formats using your finished-part schedule

Compare four sheet formats for 30 outer blanks of 1200 × 800mm, keeping the 1200mm direction along the sheet length. This regular-grid calculation uses 10mm outside trim at every sheet edge and a 3mm kerf between blanks. The production layout uses your actual allowances and permitted orientation.

Fixed-orientation grid for 1200 × 800mm blanks; no rotation or mixed nesting
Sheet formatUsable width / lengthBlanks per sheetSheets / purchased area for 30
1220 × 2440mm1200 / 2420mm1 × 2 = 215 / 44.6520m²
1220 × 2500mm1200 / 2480mm1 × 2 = 215 / 45.7500m²
1500 × 3000mm1480 / 2980mm1 × 2 = 215 / 67.5000m²
1530 × 3100mm1510 / 3080mm1 × 2 = 215 / 71.1450m²

Two 800mm columns require 1603mm including the separating kerf, beyond every usable width in this comparison. Three 1200mm rows require 3606mm, beyond every usable length. All four formats therefore yield two blanks in this fixed-orientation grid.

The 30 blanks total 28.8000m². After the rectangular openings, retained panel area totals 21.6000m². Compare those quantities with the purchased sheet area, then review any useful offcuts or permitted alternative layouts for your order.

If you want to recover the centre as another component, add its required size and finish to the cutting list. A routed 600 × 400mm opening removes material along the tool path, so the recovered piece needs its own dimensions, corner geometry, face direction and edge quality. Plan its workholding and release sequence before cutting.

Group parts by drawing revision, handedness and matching set. Mark them away from visible faces and keep their identities through coating and packing so the workshop can receive them in assembly order.

A SAMPLE FOR YOUR NEXT WORKSHOP DECISION

Try the face, opening or fitting before the bulk order

Material and appearance

Review the chosen 18mm construction, both faces, exposed layers, measured thickness and intended finish. Include the clear-finish or painted appearance you want to carry into production.

Machined connection

Choose a sample around the opening edge and nearest fixing. Include the actual backing, hardware and protection, then measure the completed bore, installed stack and tool access.

Keep the drawing revision, construction, coating and hardware with the selected sample. A full assembly or performance assessment uses the geometry, supports and method required by the project; the local fitting sample helps your workshop resolve preparation, finish and installation.

MARINE REQUIREMENT AND ORDER DOCUMENTS

Prepare the product information for purchasing approval

For a BS 1088:2018 project, include the required class and construction with your order. BSI identifies standard and lightweight marine plywood classes. We connect the relevant product information to the timber, thickness and layup you select.

BSI — BS 1088:2018, Marine plywood requirements

Request the report and sample reference for the identified 18mm, eleven-ply, 1220 × 2440mm configuration with reported density of 599kg/m³. The report records selected BS 1088-1:2003 checks and Class 3 bonding quality. The 540kg/m³ Okoume calculations on this page remain a separate weight-planning route. Each order line carries the corresponding core, dimensions and product records.

Add any structural, fire, emissions or finished-assembly requirement to the purchasing brief. The report identity, issuing organization, method, panel description and results help your team review the selected product. Our BS 1088 buying guide and production and quality page provide further order and inspection guidance.

FROM SELECTED SAMPLE TO IDENTIFIED DELIVERY

Check the panel at each supplied stage

Agree acceptance limits and records before placing the order
StageCheck and recordResolve before proceeding
Incoming sheetsConstruction identity, face/back reference, dimensions, thickness readings and condition.Mismatch with the quoted layup or evidence; damage and dimensional exceptions.
After machiningOpening location, corner profile, retained widths, hole positions and exposed edge condition.Breakout, unexpected internal discontinuities or conflicting holes and backing footprints.
After protectionCovered edges and hole walls, finished bore, fitting surfaces and any reworked areas.Bare wood from later adjustments, obstructed fit or an incomplete finish sequence.
Assembly trialActual hardware, backing, installed stack, access, projection and final mass if required.Assembly interference or unmet project checks; a fit trial alone is not a load test.
Packing and receiptPart counts, revision labels, protection, packing condition and shipment references.Mixed revisions, missing pieces, moisture exposure or transport damage.

Agree the sampling and measurement positions for your sheet or machined part. Keep photographs and readings with the part ID, drawing revision and order reference so production and receiving can review the same detail. The packing list then connects the construction, quantity and supplied work to the delivery.

PLAN YOUR PANEL ORDER

Choose the panel. Prepare the part. Move the order forward.

Bring the drawing or component you want to make. We help connect the 18mm construction, openings and finish to a useful sample, then quote the sheets or prepared parts your workshop needs.

18mm Marine Plywood

Your 18mm panel and factory work

  • Application, drawing or existing component
  • 18mm construction, sizes, openings and required finish
  • Quantities, product documents and delivery destination
View the product specification

Choose a sample for your project

Your actual opening and fitting detail

Try the actual opening, hole or fitted corner in your selected construction. Include backing, hardware and the protective finish so your workshop can review the finished fit and access.

Review this product’s sample plan

For a quotation, add your quantity, destination and required timing. You can start with the details you already have.

PanelSource · Xuzhou PanelSource Co., Ltd.
https://www.plywoodsupplier.cn/product/18mm-marine-plywood/
sales@plywoodsupplier.cn

SAMPLES & ORDER PLANNING

Plan the first order.

Samples
Standard samples without special work or a logo have no sample charge; delivery is separate. Custom samples are agreed individually.
Order quantity
Our starting guidance is one container for standard sizes and 3,000–10,000 pieces for custom sizes or designs. Tell us your trial quantity.
Production
All products are made to customer order. Production takes 10–15 days; the order confirmation records the start date and production schedule. Sea transit is additional.
Payment
Where a deposit applies, our standard reference is 30% before production, with the balance after inspection and before loading. T/T or L/C terms are agreed for the order.
Shipping
Panel orders ship by container. Share your destination so we can arrange the loading plan and quote the freight separately from production.
After-sales warranty
All products include a 180-day after-sales warranty. Contact our team with the order reference and details of any product concern.

Tell us your quantity, sample needs and target delivery date. We’ll put the price, payment terms and production schedule into your quotation.

PRODUCT-SPECIFIC QUESTIONS

Questions about 18mm Marine Plywood

What can I use 18 mm marine plywood for?

Order it for boat interiors, supported sole panels, bulkheads, access surrounds and fitted components. Bring the material and connection requirements from your design; we help prepare the selected construction and factory processing.

How many plies does your 18 mm marine plywood have?

Our listed 18 mm construction has eleven plies. Choose the face, reverse and inner veneers together, including all-Okoume or a selected hardwood construction, with the appearance and dimensional limits for your order.

Is 18 mm the same as 3/4-inch marine plywood?

Three-quarter-inch is 19.05 mm, which is 1.05 mm thicker than 18 mm. Send the required measured interval and supply stage for your fitting so the quotation and delivered panel use the right dimensions.

What sheet sizes and cut parts can I order?

Choose 1220 × 2440, 1220 × 2500 or 1220 × 3050 mm standard formats, or 1500 × 3000 and 1530 × 3100 mm project formats. Send a cut schedule for blanks or machined parts with the selected construction, dimensions and quantity.

Can you supply waterproof plywood for marine or wet-area parts?

Yes. We help choose the 18 mm marine panel with the coating and protection needed by the component. Include fresh cuts, opening walls, holes and installation changes in the treatment plan.

How much does an 18 mm marine plywood sheet weigh?

For 1220 × 2440 × 18 mm, the 540 kg/m³ Okoume planning configuration gives about 28.9 kg. The separate 599 kg/m³ configuration in the SGS report gives about 32.1 kg at those nominal dimensions. Finish, fittings and packing are additional.

Which construction does the SGS report cover?

The report identifies an 18 mm, eleven-ply, 1220 × 2440 mm configuration and records 599 kg/m³ density. It includes selected BS 1088-1: 2003 checks and Class 3 bonding quality. Send your required edition and construction so we can prepare the relevant documents for the order.

Can you prepare openings, holes and protected edges?

Yes. Send opening positions, corner geometry, hole patterns and the factory work required. We can prepare the sample and machining schedule with exposed edges and hole walls included in the selected protective process.

How do I plan backing plates and bolt length?

Use the complete fitting detail. Include the opening, backing footprint, tool access and assembled stack of panel, base, bedding, finish, backing, washers and nut. The worked diagrams show how these dimensions interact before you choose the hardware.

Will coating change the hole or fitting clearance?

Yes. Coating on both hole walls reduces the bore. Trial the planned machining and finishing sequence with the actual fitting, and include protection of wood exposed by later reaming or adjustment.

Which sample should I request?

For a fitted part, request the critical corner, opening or fastening detail in the selected construction, with its backing and finish. A face-and-edge sample helps compare appearance; the working detail lets your workshop review the actual fit and access.

What are the production, shipping and warranty terms?

Available to order, normally with 10–15 days production and container shipping. Freight terms are agreed for the specific order. Our 180-day after-sales warranty applies. Send your sizes or drawing, quantities and destination for a factory quotation.

Compare the adjacent options

CONTACT OUR FACTORY

Let’s prepare your 18mm marine plywood order.

Send the part drawing or sheet list with quantities and destination. We help complete the core, faces, processing and documents, then arrange the sample and factory quotation.

  • Thickness and construction: 18mm, eleven plies; selected veneer species and layup included in the order.
  • Face and core choices: Okoume, Sapele or Marine Birch faces; all-Okoume, Sapele/Mahogany or selected Eucalyptus/Birch core constructions.
  • Surface selection: A/B or B/BB for the technical configurations; visible faces, repair range and chosen finish recorded with the sample.

Have a fitting drawing or a current panel reference? Email it to sales@plywoodsupplier.cn. Start with the details you have; we’ll help you work through the rest.

Send us your panel requirements.

Tell us your panel, dimensions, quantity and destination port.

Request a quote ↗